Spatial Distribution of Foundation Subsoil Parameters of a Distressed Storey Building, FUT, Akure, Southwestern Nigeria

Authors
  • O. A. Ademeso

    Department of Geology, Federal University of Technology, Akure, Nigeria.

    Author

  • A. R. Ogundele

    Centre for ICT and Applied Geoinformatics, Km 4, New Ikirun Road, Osogbo, Osun State, Nigeria.

    Author

Keywords:
Array, Array, Array, Array, Array, Array
Abstract

Accurate mapping of soil properties and their spatial distribution are essential components in the understanding of geotechnical data from site investigation. The main objective of this study is to measure the properties and plot the spatial variability of foundation subsoil of a distressed storey building in FUT, Akure. For this purpose, combination of conventional analytical methods and geostatistical methods were used to analyze the data for the spatial variability. A total of 32 samples from 12 trial pits were collected, and natural moisture contents (NMC), specific gravity, grain size analysis, Atterberg limits, and compaction properties were determined using the standard analytical methods. The use of the Inverse Distance Weighting interpolation technique was the best for plotting direct visualization of the soil properties (spatial diagrams). Using the overlay technique in GIS environment, evaluation of spatial maps indicated that the Natural Moisture Contents (NMC), %Fines, Plasticity Index (PI), and Maximum Dry Density (MDD), that presented very close similarities, produced a spatial diagram that classified the area into four (A, B, C, and D) with three strength classes. Two of the parts (A and D) are of high strength, while B and C are of medium and low strengths, respectively. The parts with low/medium strength occupy more than eighty percent of the study area. The crack lines are either very close to or fall on the three different strength classes' interfaces. Generally, the subsoil possesses parameters that are unsuitable for foundation purposes. These characteristics may have led to differential settlement, which could be responsible for foundation failure, that manifested as cracks on the walls of the building.

Author Biographies
  1. O. A. Ademeso, Department of Geology, Federal University of Technology, Akure, Nigeria.

    Department of Geology, Federal University of Technology, Akure, Nigeria.

  2. A. R. Ogundele, Centre for ICT and Applied Geoinformatics, Km 4, New Ikirun Road, Osogbo, Osun State, Nigeria.

    Centre for ICT and Applied Geoinformatics, Km 4, New Ikirun Road, Osogbo, Osun State, Nigeria.

References

Ademeso O. A. (2009). Deformation traits in the Charnockitic rocks of Akure area, Southwestern Nigeria. Asian Journal of Earth Sciences vol. 2(4), pp 113-120.

Ademeso O. A. (2010). Field and Petrographic Relationships Between the Charnockitic and Associated Granitic Rock, Akure Area, Southwestern Nigeria”. World Academy of Science, Engineering and Technology, vol. 71, pp 626-630.

Ademeso, O. A., Ademeso, V. F., and Faseki, O. E. (2016). Investigation of Subsurface for Engineering Applications using Standard Penetration Tests in Ikoyi, Lagos, Southwest Nigeria. Int. J. Eng. Sci. Vol. 5(2), pp 6-18..

Adepoju, E. A., 2018. Geological Mapping of the Federal University of Technology, Akure, Ondo State, Southwestern Nigeria. Unpublished Project Report, 67p

Akpokodje, E. G. (1986). The Geotechnical Properties of Lateritic and Non-Lateritic Soils of Southeastern Nigeria and other Evaluation for Road Construction. Bull Int, Assoc. Eng. Geol. Vol. 33, pp 115-121

Bayode, S. A., Akinlalu, A., Falade, K., Oyanameh, O. E. (2020). Integration of Geophysically Derived Parameters in Characterization of Foundation Integrity Zones: An AHP Approach. Heliyon 6 e03981 https://doi.org/10.1016/j.heliyon.2020.e03981

BS 1377 (1990). Methods of Testing Soils for Civil Engineering Purposes. Prentice-Hall, New Jersey. 7p.

Burland, J. B., Broms, B. B., and DeMello, VFB, (1977). Behavior of Foundations and Structures: State-of-the-Art Report. Proceedings of the Ninth International Conference on Soil Mechanics and Foundation Engineering, Japanese Geotechnical Society, Tokyo, vol. 2, pp. 495-546.

Federal Ministry of Works and Housing (1997). General Specification for Roads and Bridges. Vol. II pp 145-284

Fromm H, Winter K, Filser J (1993) The influence of soil type and cultivation system on the spatial distributions of the soil fauna and microorganisms and their interactions. Geoderma vol 60, pp 109–118.

Gambo H. Y., Umar H., Abdulfatah A. Y. and Aminu S. (2013). Geotechnical investigation into the causes of cracks in building: A case study. EJGE Vol.18, pp 2823- 2833. https://www.researchgate.net/publication/269103997.ris

Jegede, G., (1997)., Highway Pavement Failures Induced by Soil Properties Along the F209 Highway at Omuo-Oke, Southwestern Nigeria. Nigeria Journal of Science Vol. 31, pp 121 – 126.

Jimoh, M. O. and L. B. Amuda. (2017). Cracks in Estate Buildings: A Case Study of Harmony Estate, Ilorin, Nigeria. Epistemics in Science, Engineering and Technology, Vol. 7, issue 1, pp 532-538

Journel, A.G., and Huijbrechts. C.J. (1978)., Mining Geostatistics. London Academic Press, London. 600p

Kashyzadeh, K. R. and Kesheh. N. A. (2012). Study type of Cracks in construction and its controlling. International Journal of Emerging Technology and Advanced Engineering. Vol. 2 issue 8, pp 1-4

Liu L, Wang H, Dai W, Lei X, Yang X, Li X (2014) Spatial Variability of Soil Organic Carbon in the Forestlands of Northeast China. J For Res vol. 25(4), pp 867–876

Madedor, A. O., (1986). Pavement Design Guidelines and Practice for different Geological Areas in Nigeria: Ola, S. A. (Editor). Tropical soils of Nigeria in Engineering, Practices Balkema Publishers Rotterdam, Netherlands. pp:291-298

Matheron, G. (1963). Principles of Geostatistics. Economic Geology vol. 58,1pp 246-1266.

Min, Y. K. (2006) “Cracks and How Damaging Are They?” JURUTERA; A Monthly Bulletin of the Institution of Engineers, Malaysia.pp, 18-25

Olarewaju V.O. (1987): Charnockite-granite Association in SW Nigeria: rapakivi granite type and charnockitic plutonism in Nigeria? Journal of African Earth Sciences, vol. 6, issue 1, pp 67-77.

Olarewaju, V. O., 2006. “The Charnockitic Intrusives of Nigeria." In: Oshin, O. (Ed.), The Basement Complex of Nigeria and its Mineral Resources. Akin Jinad & co, Ibadan, Nigeria, pp 45-70.

Oloruntola M., Bayewu, O., Kehinde, K., Obasaju, D. O. and Mosuro, G. (2018). Profiles of Problematic Soils and Spatial Distribution: Implication on Foundation Construction in Parts of Kosofe Lagos, Southwestern Nigeria. GeoScience Engineering vol. 64, 4, pp. 11 – 22,.

Owolabi, T. A. and Aderinola, O.S. (2014): Geotechnical Evaluation of Some Lateritic Soils in Akure South, Southwestern Nigeria. EJGE, vol. 19,: pp. 6675-6687

Oyeyemi, K. D., and Olofinnade, O. M. (2016). Geoelectrical Geotechnical studies for near surface characterization, case history: Lagos SW Nigeria. Electronic Journal of Geotechnical Engineering, vol 21(10) pp 3735– 3750.

Oyeyemi K. D., Olofinnade O.M., Aizebeokhai A. P., Sanuade O. A., Oladunjoye M. A., Ede A. N., Adagunodo T. A. and Ayara W. A., 2020. Geoengineering site characterization for foundation integrity assessment. Cogent Engineering vol. 7: pp 1-15 https://doi.org/10.1080/23311916.2020.1711684

Pravat, K. S., Gouri, S. B., and Ramkrishna, M. (2016). Spatial Analysis of Soil Properties using GIS based Geostatistics Models. Model Earth Syst. Environ. vol. 2:107 https://doi.org/10.1007/s40808-016-0160-4

Rahaman, M. A. (1988). Recent Advances in the Study of the Basement Complex of Nigeria. Symposium on the Geology of Nigeria, Obafemi Awolowo University, Ile-Ife Nigeria. Pp 11-43

Rahaman, M. A., and Ocan, O. O. (1976). On Relationship in the Precambrian Migmatitic Gneisses of Nigeria. J. Min. and Geol. Vol. 15 (1) pp, 23-30.

Reza, S. K. Utpal Baruah, Dipak Sarkar & S. K. Singh, 2016. Spatial variability of soil properties using geostatistical method: a case study of lower Brahmaputra plains Arab J Geosci. vol. 9, pp 1-8

Safari Y, Boroujeni I. E., Kamali A,, Salehi M. H., Bodaghabadi M. B., 2013. Mapping of the soil texture using geostatistical method (a case study of the Shahrekord plain, central Iran. Arab J Geosci, vol. 6, pp 3331–3339

Sudha, K., M. Israil, S. Mittal And J. Rai., (2009). Soil characterization using electrical resistivity tomography and geotechnical investigations. J. Appl. Geophys. vol. 67, 1, pp. 74–79.

Suprenants, B. A. and Basham, K. D. (1993) Evaluating Cracks in Concrete Walls, Publication of the Aberdeen Group. 4p

Unified Soil Classification System. (1985). Classification of Soil for Engineering Purposes: Annual Book of American Society for Testing and Materials, pp.395-408

Vieira, V. A., Mello C.R., Lima J. M. (2007) Spatial variability of soil physical attributes in small watershed. Ciencia e Agrotecnologia vol. 31(5), pp 1477–1485 (in Portuguese)

Webster, R. and Oliver, M. A. (2001). Geostatistics for Environmental Scientists. John Wiley & Sons Inc. Chichester, England, 271 p..

Wigginton, J. D., Lockaby B. G., Trettin C. C., Nelson E.A., Kolka R. K., Wisniewski J (2000) Soil Organic Matter Formation and Sequestration across a forested floodplain chronosequence. In: Proceeding of Workshop held at Clemson University, 12–14 April 1999, pp 141–155

Dixon K. and Wright P. H. (2003). Highway Engineering, Seventh Edition, John Willey, and Sons: New York, 688p.

Yao, L. X., Zhou, X. C., Cai, Y. F., Chen, W. Z., 2004. Spatial variability of soil properties at different sampling intensities and accuracy of their estimation. Soils, vol. 36:538-542

Zheng, Z., Zhang F. R., Ma, F. Y. (2009) Spatiotemporal Changes in Soil Salinity in a Drip Irrigated Field. Geoderma vol. 149, pp 243–248

Zhu, X. H., Yang, X. C., Cai, Y. L. (2005). Fractal and fractal dimension of spatial distribution of China soil system. Acta Pedol Sin vol. 42, pp 881-888 APPENDIXES Output raster (optional) The output raster. This raster is required output only if no output geostatistical layer is requested. Output cell size (optional) The cell size at which the output raster will be created. This value can be explicitly set under Raster Analysis from the Environment Settings. If not set, it is the shorter of the width or the height of the extent of the input point features, in the input spatial reference, divided by 250. Power (optional) The exponent of distance that controls the significance of surrounding points on the interpolated value. A higher power results in less influence from distant points. Search neighborhood (optional) Defines which surrounding points will be used to control the output. Standard is the default. Standard Major semiaxis—The major semiaxis value of the searching neighborhood. Minor semiaxis—The minor semiaxis value of the searching neighborhood. Angle—The angle of rotation for the axis (circle) or semimajor axis (ellipse) of the moving window. Maximum neighbors—The maximum number of neighbors that will be used to estimate the value at the unknown location. Minimum neighbors—The minimum number of neighbors that will be used to estimate the value at the unknown location. Sector type—The geometry of the neighborhood. One sector—Single ellipse. Four sectors—Ellipse divided into four sectors. Four sectors shifted—Ellipse divided into four sectors and shifted 45 degrees. Eight sectors—Ellipse divided into eight sectors. Smooth Major semiaxis—The major semiaxis value of the searching neighborhood. Minor semiaxis—The minor semiaxis value of the searching neighborhood. Angle—The angle of rotation for the axis (circle) or semimajor axis (ellipse) of the moving window. Smoothing factor—The Smooth Interpolation option creates an outer ellipse and an inner ellipse at a distance equal to the Major Semiaxis multiplied by the Smoothing factor. The points that fall outside the smallest ellipse but inside the largest ellipse are weighted using a sigmoidal function with a value between zero and one. Standard Circular Radius—The length of the radius of the search circle. Angle—The angle of rotation for the axis (circle) or semimajor axis (ellipse) of the moving window. Maximum neighbors—The maximum number of neighbors that will be used to estimate the value at the unknown location. Minimum neighbors—The minimum number of neighbors that will be used to estimate the value at the unknown location. Sector type—The geometry of the neighborhood. One sector—Single ellipse. Four sectors—Ellipse divided into four sectors. Four sectors shifted—Ellipse divided into four sectors and shifted 45 degrees. Eight sectors—Ellipse divided into eight sectors. Smooth Circular Radius—The length of the radius of the search circle. Smoothing factor—The Smooth Interpolation option creates an outer ellipse and an inner ellipse at a distance equal to the Major Semiaxis multiplied by the Smoothing factor. The points that fall outside the smallest ellipse but inside the largest ellipse are weighted using a sigmoidal function with a value between zero and one. Weight field (optional) Used to emphasize an observation. The larger the weight, the more impact it has on the prediction. For coincident observations, assign the largest weight to the most reliable measurement. Input features The input point features containing the z-values to be interpolated. Z value field Field that holds a height or magnitude value for each point. This can be a numeric field or the Shape field if the input features contain z-values or m-values. Output geostatistical layer (optional) The geostatistical layer produced. This layer is required output only if no output raster is requested. Output raster (optional) The output raster. This raster is required output only if no output geostatistical layer is requested. Output cell size (optional) The cell size at which the output raster will be created. This value can be explicitly set under Raster Analysis from the Environment Settings. If not set, it is the shorter of the width or the height of the extent of the input point features, in the input spatial reference, divided by 250. Power (optional) The exponent of distance that controls the significance of surrounding points on the interpolated value. A higher power results in less influence from distant points. Search neighborhood (optional) Defines which surrounding points will be used to control the output. Standard is the default. Standard Major semiaxis—The major semiaxis value of the searching neighborhood. Minor semiaxis—The minor semiaxis value of the searching neighborhood. Angle—The angle of rotation for the axis (circle) or semimajor axis (ellipse) of the moving window. Maximum neighbors—The maximum number of neighbors that will be used to estimate the value at the unknown location. Minimum neighbors—The minimum number of neighbors that will be used to estimate the value at the unknown location. Sector type—The geometry of the neighborhood. One sector—Single ellipse. Four sectors—Ellipse divided into four sectors. Four sectors shifted—Ellipse divided into four sectors and shifted 45 degrees. Eight sectors—Ellipse divided into eight sectors. Smooth Major semiaxis—The major semiaxis value of the searching neighborhood. Minor semiaxis—The minor semiaxis value of the searching neighborhood. Angle—The angle of rotation for the axis (circle) or semimajor axis (ellipse) of the moving window. Smoothing factor—The Smooth Interpolation option creates an outer ellipse and an inner ellipse at a distance equal to the Major Semiaxis multiplied by the Smoothing factor. The points that fall outside the smallest ellipse but inside the largest ellipse are weighted using a sigmoidal function with a value between zero and one. Standard Circular Radius—The length of the radius of the search circle. Angle—The angle of rotation for the axis (circle) or semimajor axis (ellipse) of the moving window. Maximum neighbors—The maximum number of neighbors that will be used to estimate the value at the unknown location. Minimum neighbors—The minimum number of neighbors that will be used to estimate the value at the unknown location. Sector type—The geometry of the neighborhood. One sector—Single ellipse. Four sectors—Ellipse divided into four sectors. Four sectors shifted—Ellipse divided into four sectors and shifted 45 degrees. Eight sectors—Ellipse divided into eight sectors. Smooth Circular Radius—The length of the radius of the search circle. Smoothing factor—The Smooth Interpolation option creates an outer ellipse and an inner ellipse at a distance equal to the Major Semiaxis multiplied by the Smoothing factor. The points that fall outside the smallest ellipse but inside the largest ellipse are weighted using a sigmoidal function with a value between zero and one. Weight field (optional) Used to emphasize an observation. The larger the weight, the more impact it has on the prediction. For coincident observations, assign the largest weight to the most reliable measurement.

Downloads
Published
2021-06-30
Section
Articles